John-wood Superflue Power Vent (before FVIR technology) Bedienungsanleitung

INSTALLATION AND OPERATING INSTRUCTIONSRead these instructions thoroughly before startingPOWER VENTED GAS FIRED WATER HEATERPART NO. 63817 REV. K (05-

-8-The discharge line from the temperature and pressurerelief valve must:1. not be smaller than the outlet pipe size of the valve.2. not be threaded,

-9-L1NGG = GREENN = WHITEL1 = BLACK5 = YELLOW7 = BLUECONNECTORAIR PRESSURE SWITCHJUNCTION BOXBLOWERIGNITORFLAME SENSORCONNECTORWIRING DIAGRAMHIGH LIMI

-10-1. Has the gas piping been leak tested?2. Is the heater connected to the correct gassupply as shown on the rating plate (NaturalGas / Propane)?3.

-11-What to Do If You Smell Gas• Turn the gas shut-off valve in the gas supply line tothe heater to ‘OFF’.• Do not try to light any appliance.• Do not

-12-Service and maintenance of the heater should be performedat regular intervals. The following is a service recommenda-tion for the homeowner.At all

-13-LIMIT SWITCHWIRESDRAFT HOODAIR PRESSURETUBINGMOTOR VEN-TILATIONOPENINGSBLOWERMOTORAIR INTAKE OPENING FORDRAFT HOODLIMIT SWITCHFigure 12Flushing of

-14-Figure 15 (continued)Figure 15Figure 13Cast Iron Burner1. Observe the flame pattern on the burner.2. Observe the primary air openings of the burne

-15-To replace an anode:1. Turn off gas/ power. (Follow “To Turn Off Gas toAppliance” section)2. Shut off the cold water supply valve to the heater.3.

-16-Keep the area around the heater clear and unobstructed.Keep safety your first priority. Take allprecautions to avoid creating a fire, health or sa

-17-ROBERTSHAW 7222WDER SEQUENCE OF OPERATIONWhen initially energized, the 7222WDER control will perform a self-diagnostic check and the red LED will

REPLACEMENT PARTS LISTINGFLOOR DRAIN18. T & P VALVE19. DRIPTUBE20. BAFFLE ASSEMBLY21. CONTROL VALVE22. CONTROL VALVE COVER23. INNER GAS DOOR24. OU

See Rating Label Serial Number prefix forWarranty Code. Reduced warranty periodapplies to Newfoundland.Warranty Code: P R S T U V W YStandard Warranty

PART NO. 73902 REV. A (06-12)INSTRUCTION SHEETPVC VENT SYSTEM ADAPTORPlease Read And Understand These Instructions Thoroughly Before StartingWARNING:D

-1-I) DESCRIPTIONThe “Superflue” series of water heaters can be installedto vent the products of combustion horizontally throughthe wall or vertically

-2-SAFETY WARNINGWater heaters are heat producing appliances. Toavoid damage or injury, there shall be no materialsstored against the water heater and

-3-(b) Air from OutdoorsA confined space shall be provided with two permanentopenings: one near the top, and one near the bottom ofthe enclosure. Thes

-4-1. EACH 2” (50mm) 90° ELBOW USES 5 EQUIVALENT FEET (1.5 METERS).2. EACH 3” (75mm) 90° ELBOW USES 7 EQUIVALENT FEET (2.1 METERS).3. ONE 2” (50mm)

-5-TERMINATION MAY BE90 DEGREE ELBOW OR A “T” ELBOW3” MIN. LENGTHROOF LINE18” VERTICAL VENTING(MUST BE SUPPORTED EVERY 8’)A vent used in a SPECIAL VEN

-6-3) BLOWER RUBBER COUPLING CONNECTION(See figure 5) 1. Clean and slightly sand the end of the vent pipethat will connect to the rubber coupling. Thi

-7-All leak testing must be done with a soapy water solu-tion or equivalent leak test liquid. Never use a match oropen flame to test for gas leaks. A